(800)865-5931 Monday to Friday 8:00 AM - 5:00 PM Central
0
Free Shipping See Details
|
No Sales Tax See Details

Compare Items

Please feel free to compare as many items as you would like. There is no limit to what you can compare.

Additonally, if you have questions while comparing products please do not hesitate to contact us with any question you may have.

(800) 865-5931

  • Amperage

    The amps that the unit is designed to operate at.

    Amperage
  • Voltage
  • Frequency
  • Speed(s)

    The number of speeds a motor runs at. Motors with 4 speeds can run at High, Medium High, Medium Low, and Low. Motors with 2 speeds can run at either high or low speed.

    Speed(s)
  • Horse Power

    The amount of power generated by the motor. One horsepower (HP) is equivalent to 746 watts.

    Horse Power
  • Revolutions Per Minute

    Rotational speed in revolutions per minute

    Revolutions Per Minute
  • Bearing

    Basic types include: Sleeve - Preferred where low noise level is important, as on fan and blower motors. Unless otherwise stated, sleeve bearing motors listed can be mounted in any position, including shaft-up or shaft-down. Ball - Used where higher load capacity, either axial or radial, is required or where shaft speed is lower than 500 RPM. Shields, metal rings with close running clearance one one side (sigle-shielded) or both sides (double-shielded) of bearing, and seals, which are similar except with rubber lips that press against inner race, more effectively excluding dirt, ect., are two barriers used to keep out dirt.

    Bearing
  • Ambient

    The temperature of the space around motor. Measured in Celcius (40 degrees celcius equals 104 F).

    Ambient
  • Mounting

    Resilient Mounting - Sometimes called rubber or hub mounted - motor shell is isolated from base by vibration absorbing material, such as rubber rings on the end shields, to reduce transmission of vibration to the housing of the unit or appliance. Stud Mounting - Motor has bolts extending from from front or rear, by which it is mounted. Often used on small, direct drive fans and blowers.

    Mounting
  • Rotation
  • Replaces

    Type of motor this model replaces.

    Replaces
  • Shaft Dimensions

    Width of the shaft (usually 1/2") x the Length of the shaft.

    Shaft Dimensions
  • Thermal Overload Protection

    A temperature or current sensing device usually integral within the motor, that disconnects the motor winding from its power source to prevent overheating due to overload or failure to start. Automatic Reset(Auto) - After Motor cools, protector automatically restores power. Should not be used where unexpected restarting would be hazardous.

    Thermal Overload Protection
  • Total Length (Inches)

    Total length (in inches) of motor and shaft.

    Total Length (Inches)
$89.99
(0 Reviews)
  • 2.6 Amps
  • 208 / 230 Volts
  • 60 Hz
  • 1 (2 taps)
  • 1/3 - 1/6 HP
  • 1,075 RPM
  • Ball
  • 60 Degree Celcius
  • Stud
  • Reversible
  • 1075 RPM 1/3 to 1/6 H.P. Condenser Fan Motors
  • 1/2 x 5 Inches
  • Auto
  • 9.6 inches
$118.99
(0 Reviews)
  • -
  • 208 / 230 Volts
  • 60 Hz
  • 2
  • 1/3 - 1/6 HP
  • 825 RPM
  • Ball
  • 60 Degree Celcius
  • Stud
  • Reversible
  • 825 RPM 1/3 to 1/6 H.P. Condenser Fan Motors
  • 1/2 x 5 Inches
  • Auto
  • -

In 2002 Alpine Home Air Products became the first company to sell heating, air conditioning and indoor air-quality products online. We have proudly served hundreds of thousands of customers, helping them save time and money by buying their products direct.